Andalusite is an alumina-silicate raw material used principally in the manufacture of heat resistant refractory products. When andalusite is produced, unlike many other refractory raw materials, costly calcining is not required. On firing refractory raw materials containing andalusite, high strength mullite is formed, resulting in the superior qualities of.
Yayang Product Page
a) Andalusite conversion to mullite at relatively low temperatures, imparting high hot strength and resistance to physical-chemical erosion, with very good resistance to slag penetration and alkali attack.
b) Minimum volume change when firing andalusite - containing refractory materials; dimension control of the refractory is improves.
c) High creep and abrasion resistance, high strength at high temperatures, resistance to chemical and physical erosion.
d) The very low volume change on firing is also advantageous when andalusite is used in monolithic refractories.
e) Resistance to attack and penetration by slag and gases.
f) The low flux content helps the resistance to slags and alkalies.
Our company's expert technical team will be happy to assist you.
Application Areas;
Andalusite-based refractories are used principally in iron and steel making, mostly in monolithic linings in blast furnaces, stove brick and checkers, torpedo transfer, hot metal mixers, casting ladles, and induction furnaces, Andalusite shapes are used in cement kilns, the glass industry, in and in induction furnaces. Andalusite refractories are also used effectively under abrasive conditions where high loads and high temperatures exist Also in stack linings and kiln furniture, monolithic castable linings, ramming mixes and heat exchangers, heat treatment furnaces. While andalusite consumption in the Western Hemisphere has traditionally been at a low level, because of restricted availability, industrial furnaces in the world have now the opportunity to reduce costs by effectively utilizing a world class andalusite. Typical physical / chemical characteristics of the our andalusite are 59% Al2O3 and Fe2O3 0.80%. Contact our company for other technical specifications.
Refractory Industry; There are many benefits of using andalusite in refractory applications. Volume stability, Very good creep resistance and refractoriness under load, High thermal shock resistance, Good chemical attack, slag and metal penetration resistance.
Casting Industry; In the modern sand casting process, andaluzite-based special sands are used to increase casting quality and reduce the risk of defects. Due to its low thermal expansion and high refractoriness, Andalusite is the ideal solution for iron and steel casting without veins and finishes.
Ceramic Industry; Andalusite is a natural source of alumina and mullite that can be profitably used when the physical and chemical properties of your ceramic material support need to be better controlled. Due to its high purity and very fine particle size distribution, micronized andalusite is an efficient and economical alternative to zircon silica as opacifier for glazes and engobes.
Furnace Furniture Industry; Andalusite thermal shock resistance, volume stability and high temperature load resistance uniquely combine in this naturally occurring crystal
CONFERENCE
Merits of using andalusite-based refractories compared to bauxite-based refractories
M. Nyoka; D. Brazier; T. Courtney; R.A. Parry
Vereeniging Refractories (Pty) Ltd
ABSTRACT
Historically bauxite-based refractories have been used in applications where andalusite-based refractories could work. Bauxite-based refractories were chosen over andalusite-based refractories mainly because of the availability of low-cost Chinese bauxite and also because many furnaces were designed by international companies that cannot easily access high-quality products. Currently, the availability of low-cost bauxite is under threat as a result of high export duties and tariffs as well as restrictions on the amount of material that China allows to be exported. South Africa is a major producer of andalusite, and this guarantees stability with respect to both availability and price. Refractories based on andalusite have an added economic advantage over bauxite-based refractories in that unlike bauxite, which requires high-temperature calcination before use, andalusite is used in its raw state. This paper constitutes a literature study of the merits, both technical and economic, of using refractories based on andalusite compared to bauxite-based refractories.
Keywords: bauxite, andalusite, refractory, furnaces, calcination.
Introduction
The refractory industry in recent years has witnessed a dramatic increase in the cost of virgin raw materials. This has been largely due to increasing development in the Asian market, particularly India and China, where owing to domestic demand materials such as bauxite and magnesia are no longer readily available for export (Buhr and Spreij, ; Industrial Minerals; Hutton, Yates, and Green, ; Buhr et al., ; Schmidt-Whitely, ; Feytis, ; Tran, ; Wanecq, ; O'Driscoll, ; Saxby, ). In the s low-priced Chinese bauxite replaced other alumina-bearing materials such as andalusite, mullite, and in some instances even chamotte. At that time it was easy for refractory suppliers to provide their customers with new refractories having higher alumina contents (Buhr and Spreij, ). The general perception was that a higher alumina content meant superior performance. For this reason, bauxite-based refractories became a preferred option where a higher alumina content was required. With raw materials being the major cost driver in the refractories business, many refractory producers outside China are facing an uncertain future. Escalating costs and falling quality of imported Chinese raw materials put local manufacturers at significant disadvantage compared to Chinese refractory producers, who can export to South Africa at zero rate import duties (Buhr and Spreij, ; Feytis, ; Saxby, ). The situation has since changed in the past years, especially since (Buhr and Spreij, ). This is illustrated in Figure 1.
The objective of this paper is to show that the usage of andalusite refractories could be revived in applications where they have been replaced by bauxite. This is driven by both technical and economic factors.
Availability of raw materials
Andalusite
Andalusite supply is fairly tight, with commercial sources limited to South Africa, which is the major producer, and France (Feytis, ; Xiong, ). Damrec, through its subsidiary Samrec, has four andalusite mines in South Africa producing more than 200 000 t/a. Andalusite Resources, an alternative supplier, operates close to the Thabazimbi andalusite facility of Imerys, owned by Damrec (Feytis, ). China produces andalusite on a smaller scale, mainly for domestic uses. The typical composition of South African andalusite deposits is given in Table I.
Bauxite
The typical chemical analysis for refractory grade bauxite is given in Table II.
The refractories industry is in general dependent on China for raw materials, for example 95% of refractory bauxite production is controlled by China (Buhr and Spreij, ; Hutton, Yates, and Green, ; Schmidt-Whitely, ; Wanecq, ; O'Driscoll, ). China is also a major supplier of refractories (Buhr and Spreij, ). In China the introduction of environmental regulations and energy efficiency policies resulted in the closure of highly polluting shaft and round kilns (Hutton, Yates, and Green, ). Although welcomed environmentally, this move led to shortages in raw materials and increased costs. On the other hand, China changed its policy, and now discourages the export of raw materials (Buhr and Spreij, ; Hutton, Yates, and Green, ; O'Driscoll, ). This has been brought about by limiting the volume of material by imposing a system of export licenses, fees, and taxes. Exports of raw materials such as dead-burned magnesite, graphite, and bauxite, for example, are restricted and heavily taxed (Buhr et al., ; Tran, ; Wanecq, ):
The export tax on bauxite is 15%
Export licenses are auctioned to selected domestic bidders only
The export license cost far exceeds the issue price
An output VAT of 17% is raised (from ).
None of these costs are borne by Chinese domestic producers, and exports of finished products made from these raw materials are not taxed (Buhr and Spreij, ). The result of these measures has been a steep rise in price in the global market. It is important to note that refractory product exports are not subject to such limitations. Due to the licensing and taxation of exported raw materials, Chinese domestic producers of refractories enjoy a cost advantage in export markets (Buhr and Spreij, ; Tran, ; Wanecq, ).
The net result of these measures by China is that international demand for raw materials exceeds supply, and the resulting increase in costs is often passed on to the user. With China being a player in the refractories business as well, this strategy is not always an advantage. To remain profitable/viable, refractory users have to turn to alternative materials that can serve the same purpose. One such example is the use of andalusite refractories in applications where bauxite is currently being used (Buhr and Spreij, ). Being a locally produced raw material, South African andalusite is not subject to export restrictions. South Africa is the major producer of andalusite, and this guarantees stability with respect to both availability and price. A stable supply of andalusite as an alternative to bauxite ensures that the local refractory manufacturing industry is protected. The local user industry is also guaranteed a consistent supply of a high-quality product that is not subject to foreign exchange fluctuations. Compared to bauxite as a refractory raw material, andalusite offers the following advantages:
An andalusite crystal remains stable with a small increase in volume after firing, and hence the internal porosity does not change. Andalusite does not, therefore, require any preparatory firing before use (Dubreuil and Sobolev, ; Hubert, ). Bauxite suitable for use as a refractory aggregate is produced by calcining the ore at -°C (Bradely and Hutton, . Calcination is done to drive off chemically combined water, to sinter the material at sufficiently high temperature for it to shrink to a higher density and low porosity, and to convert all the alumina and silica into corundum and mullite so that there is no free silica. Since andalusite does not require calcining it offers significant economies in that it saves energy, an advantage that is certain to be of importance in the light of increased energy costs (Overbeek, , Ihlen)
Andalusite offers better scope for control of dimensional tolerances and warpage, especially in the manufacture of complex shapes
Andalusite is one of the minerals that can be used at its natural grain size as an aggregate in the manufacture of refractory bricks
Andalusite has a higher chemical purity than other refractory raw materials, particularly bauxite and chamotte (Hubert, ). Furthermore, the grain size is consistent up to a few millimetres, each grain being a single monolithic crystal with a very low open porosity. The low content of impurities (Figure 2) such as Na2O, K2O, MgO, CaO, Fe2O3, TiO2 results in a small amount of glass phase at high temperatures, and as a result provides a high resistance to thermal shocks, a high deformation temperature, and a good creep resistance (Xiong, ; Hubert, ; Dubreuil, Filari, and Sobolev, ). These parameters are much higher than those of corresponding alumina-containing refractories based on bauxite, mixtures of fireclay and bauxite, or mixtures of bauxite and alumina.
The company is the world’s best andalusite powder for refractory materials supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.
The refractory characteristics of andalusite are related to its ability to form the refractory mullite phase, which combines high strength with resistance to physical and chemical corrosion at elevated temperatures (Dubreuil and Sobolev, ; Overbeek, ; Ihlen, ; Hubert, ; Dubreuil, Filari, and Sobolev, ). These properties are desirable at high temperatures and in chemically corrosive environments. In the fired state a refractory based on andalusite is composed of predominantly mullite as the major phase, together with glass, whereas a bauxite-based material is composed of corundum as the major phase with minor quantities of mullite and glass (Overbeek, ).
Advantages of andalusite-based refractories over bauxite-based refractories
High refractoriness under load
Refractoriness under load refers to the ability of a material to withstand specific conditions of load, temperature, and time (Baxendale, ). It is dependent on the softening point and the amount of glassy phase within the refractory system. Andalusite-based refractories are associated with a high refractoriness under load (Xiong, ; Hubert, ). This is due to the low volume and high viscosity of the liquid phase formed and the very rigid structure of the mullitized microstructure.
High creep resistance
Creep in compression is described as plastic deformation of a refractory under a specific stress over time. As with refractoriness under load, the ability of a refractory to withstand creep under compression depends on the softening point and the amount of glass phase in the refractory system (Baxendale, ). Andalusite-based bricks show extreme resistance to creep during thermal cycling between °C and °C (Xiong, ; Hubert, ). Because of impurities (Figure 2) in bauxite, especially alkalis, a molten phase forms at temperatures as low as °C (Buhr and Spreij, ). The presence of a molten phase decreases the creep resistance despite the overall higher alumina content of bauxite.
Good resistance to chemical attack and penetration by slag and metal
Andalusite-based refractories offer excellent resistance to penetration and attack by slag and metal. This is due to the dense, homogenous single-crystal structure, in which there are virtually no channels of weakness along which slag can permeate and travel (Buhr and Spreij, ; Dubreuil and Sobolev, ). As a result, andalusite-based refractories are superior to refractories based on chamotte, bauxite, and bauxitic clays, in which even the smallest piece of material is still a composite of minerals between which the slag can penetrate.
Thermal shock resistance
Refractories based on andalusite exhibit high resistance to thermal shock. This is attributable to their typical network microstructure (Buhr and Spreij, ; Xiong, ; Dubreuil and Sobolev, ; Overbeek, ; Ihlen, ; Hubert, ; Dubreuil, Filari, and Sobolev, ). The liquid glassy phase that is entrapped in the mullite crystal acts as a shock absorber that prevents crack initiation during thermal cycling.
Material requirements
The density difference between andalusite and bauxite refractories is typically 8-10% (Buhr and Spreij, ). Bauxite-based linings therefore have a higher material demand compared to andalusite-based linings, a factor that needs to be considered in economic comparisons of lining concepts.
Conclusion
Andalusite-based refractories possess superior critical refractory properties over bauxite based-refractories and can thus be used in applications where bauxite-based refractories are currently used. Andalusite-based refractories often confer better thermomechanical properties such as hot strength, refractoriness under load, creep resistance, and thermal shock resistance. South Africa, being the single biggest producer of high-quality refractory-grade andalusite, guarantees stability with respect to price and availability, whereas bauxite, which is an imported product, is subject to export restrictions and foreign exchange fluctuations.
References
Baxendale, S. . Testing of refractory materials. Refractories Handbook. Schacht, C.A. (ed.). CRC Press. pp. 451-473. [ Links ]
Bradely, M. and Hutton, A. . An overview of refractory raw materials -part 1, alumina. The Refractories Engineer, May. pp. 21-22. [ Links ]
Brosman, D.A. . Alumina-silica brick. Refractories Handbook. Schacht, C.A. (ed.). CRC Press. pp. 79-107. [ Links ]
Buhr, A. and Spreij, M. . Technical and economic review of high alumina refractory raw materials for steel refractories. Proceedings of the 49th Annual Conference of Metallurgists of CIM, Vancouver, BC, Canada. [ Links ]
Buhr, A., Graf, W., Power, L.M., and Amthauer, K. . Almatis global product concept for the refractory industry. Proceedings of the 9th Unified International Technical Conference on Refractories (UNITECR ), Orlando, Florida, USA, November 8-11. [ Links ]
Dubreuil, P. and Sobolev, V.M. . Andalusite: A promising material for manufacturing high quality refractories. Refractories and Industrial Ceramics, April. [ Links ]
Dubreuil, P., Filari, E., and Sobolev, V.M. . Use of andalusite refractories in ferrous metallurgy. Refractories and Industrial Ceramics, June. [ Links ]
Feytis, A. . South African andalusite expansions. Industrial Minerals, London, UK, October . [ Links ]
Feytis, A. . Andalusite resources expansion on course. Industrial Minerals, London, UK, October . [ Links ]
Feytis, A. . Refractories rising. Industrial Minerals, London, UK, September. pp 51-59 [ Links ]
Hubert, P. Andalusite: a reactive mineral for refractories. Damrec's internal document, vol. 1, . pp. 1-12. [ Links ]
Hutton, T., Yates, V., and Green, J. . Reclaimed raw material resources and their use in modern monolithic refractories. The Refractories Engineer, September. pp. 21-22. [ Links ]
Ihlen, P.M. . Utilisation of sillimanite minerals, their geology and potential occurrences in Norway - an overview. Bulletin 436, Norges Geologiske Undersorkel. pp. 113-12. [ Links ]
Industrial Minerals O'Driscoll, M. . Best of both worlds: supply and demand - China's role as a source of refractory minerals for global markets. Fourth International Symposium on Refractories, Dalian, China, 24-28 March. [ Links ]
Overbeek, P.W. . Andalusite in South Africa. Journal of the South African Institute of Mining and Metallurgy, vol. 9. pp. 157-171. [ Links ]
Qafssaoui, F., IIdefonse, J.P., Poirier, J., Hubert, P., and Daniellou, P. . Corrosion of high -alumina refractory bricks by calcium aluminate slags. Proceedings of the 8th Unified International Technical Conference on Refractories (UNITECR ), Osaka, pp. 229-232. [ Links ]
Saxby, A. . Refractories as a bauxite market; current status and future prospects. Roskill Information Services, London, UK. [ Links ]
Schmidt-Whitely, R. . The dependence of EU refractories industry on raw materials imports. SW Trade & Raw Materials, 25 August. [ Links ]
Tran, A. . Quest for calcined bauxite. Industrial Minerals, March. [ Links ]
Wanecq, F. . The importance of raw materials for the European refractory industry. European Ceramic Industry Association, 17 November. [ Links ]
Xiong, X.Y. . A refractory raw material andalusite: properties and application. Proceedings of the Conference of Metallurgists (COM ), Vancouver, BC, Canada, October 3-6. [ Links ]
© The Southern African Institute of Mining and Metallurgy, . ISSN -.
This paper was first presented at the, Refractories Conference, 23-24 April , Misty Hills Country Hotel and Conference Centre, Cradle of Humankind, Muldersdrift, South Africa.
For more information, please visit flake graphite price.